Qolsys IQ Shock Mini-S: Installation Notes

Q: Why does my zone show trouble?

Most common: low battery, tamper open, out of range, or wrong sensor type for the panel receiver (PowerG vs legacy 319/345 MHz sensors).

Q: Where is official documentation?

Qolsys product pageIQ Shock Mini S Installation ManualIQ Shock Mini S Quick GuideNPA IQ Shock Mini S Primary reference: IQ flood/temperature sensor guide

Q: How do I test after installation?

Use panel walk test, zone status, and (if monitored) central station test per dealer procedure.

Q: Can I mix PowerG and 319/345 MHz legacy sensors?

PowerG needs IQ Panel/H hub; 319/345 needs IQ Card 319/345 installed transceiver hardware — they do not enroll on the standard 345 MHz receiver alone.

On this page

Overview
Installation Notes
FAQs

Overview

PowerG flood / environmental sensor — water or temperature monitoring (IQ Flood-S, IQ Temp-S).

On IQ Panel systems, wireless devices are supervised zones on the panel — tamper, low battery, and missing signals appear as trouble conditions that may block arming depending on panel programming.

At a Glance

Specification	Details
Detection	Water probe and/or temperature
Wireless	PowerG encrypted

What This Device Does Well

Provides reliable supervised status at the panel and Alarm.com when installed, enrolled, and range-tested correctly.

Before You Service or Replace One

Sensor SKU — PowerG S-Line vs IQ Card legacy vs hardwire module.
Panel online — resolve panel AC/comms trouble before blaming sensor.
Range — sensor placement or add IQ Remote as repeater path where supported for distant zones.
Battery type — use listed cell; replace all batteries in multi-cell devices.
Tamper — cover fully closed before declaring hardware fault.

Official Sources

Use official Qolsys install PDFs and install guides for exact wiring, enrollment, and firmware — specifications vary by SKU and region.

Related troubleshooting guides

Qolsys IQ Panel alerts: low battery, tamper, supervision, and connectivity How to read and fix trouble alerts on Qolsys IQ Panel 2, IQ Panel 4, IQ Panel 5, and IQ Hub, plus PowerG vs S-Line sensors and default codes.
Alarm keeps going off for no reason? Common causes of false alarms The real reasons alarms go off on their own: misaligned door contacts, motion detectors and pets, heat and drafts, low batteries, and entry delays, and how to track down the zone responsible.
How to put your alarm system on test before working on it Avoid false dispatches and fees: how to put a monitored alarm on test with the central station, what to tell them, and how to confirm signals afterwards.
Smoke or CO detector chirping: battery, end of life, or the alarm panel? How to tell whether a chirp is a smoke detector battery, an end-of-life warning, or your security system, and how to stop it safely.
Wireless alarm sensor low battery: finding it and changing the battery How to tell which door, window, or motion sensor has a low battery, which battery it takes, and how to make the panel clear the warning afterwards.

Installation Notes

Follow IQ flood/temperature sensor guide and the official resource links in this product folder for mounting, wiring, and enrollment.

Pre-install checklist

Confirm panel model (IQ Panel 4/5/Pro/Hub) and encryption requirements.
Verify dealer cell account and module SKU before cell install.
Document installer code and existing zone map for takeover jobs.
Plan antenna routing (ANT5XL) when panel location has poor cell RSSI.
Have listed batteries and tools for sensor mounts before enrollment.

Typical install sequence

Mount and power panel; apply firmware updates per dealer bulletin.
Install cell module and run communication test / Alarm.com activation.
Enroll wireless sensors via installer Learn mode; label zones.
Include Z-Wave devices after excluding from any prior hub.
Install IQ Card for legacy sensors or optimize PowerG placement before fringe wireless devices.
Run walk test, user code training, and central station test if monitored.

Power and connectivity reference

Product type	Power	Network / RF
IQ Panel 4/5/Pro/Hub panel	AC + backup battery	PowerG sensors; IQ Cards; Z-Wave automation
Wireless sensor	Battery per SKU	PowerG encrypted; IQ Card 319/345 legacy
Cell module	Panel-powered	LTE to dealer / Alarm.com
IQ Remote keypad	PowerG link	IQ Panel host
Z-Wave module	Mains or battery per device	Z-Wave to panel

Source: IQ flood/temperature sensor guide (Qolsys official documentation).

Open the manufacturer manual

FAQs

Why does my zone show trouble?

Most common: low battery, tamper open, out of range, or wrong sensor type for the panel receiver (PowerG vs legacy 319/345 MHz sensors).

How do I replace a sensor?

Delete old zone in installer programming, enroll replacement using Learn mode, and test walk test at final location.

Will Alarm.com show this device?

When the panel has active interactive service, enrolled zones appear in the Alarm.com app with status matching the panel.

Where is official documentation?

Primary reference: IQ flood/temperature sensor guide

How do I test after installation?

Use panel walk test, zone status, and (if monitored) central station test per dealer procedure.

Can I mix PowerG and 319/345 MHz legacy sensors?

PowerG needs IQ Panel/H hub; 319/345 needs IQ Card 319/345 installed transceiver hardware — they do not enroll on the standard 345 MHz receiver alone.