Overview
HS2TCHPRO 7-inch touchscreen keypad with prox support is the Pro equivalent of Neo HS2TCHP — graphical arming and status on PowerSeries Pro Corbus.
Panel bus / link type
Corbus (PowerSeries Pro)
At a Glance
| Detail | Value |
|---|---|
| Product type | Alarm keypad / operator interface |
| Model family (HS2TCHPRO) | See label and install manual |
| Bus / wireless link | Corbus (PowerSeries Pro) |
| Primary manual | PowerSeries Pro HS2TCHPRO Installation Manual; User Guide |
| Region / listing notes | Black/white bezel SKUs — same electronics |
Before You Install or Replace One
- Confirm exact model number on the keypad label matches the install manual.
- Verify host panel family — Keybus PowerSeries, Neo Corbus, MAXSYS Combus, and IMPASSA wireless are not interchangeable.
- Plan unique keypad address or wireless enrollment — duplicates cause bus collisions or offline devices.
- Check partition assignment (global vs partition keypad) for multi-partition sites.
- Include keypad current draw in panel AUX / Corbus / battery standby calculations.
Official Sources
- Product page: DSC PowerSeries Pro Hardwired Touchscreen Keypad 7 inch with Prox Support in Black or White (ID 2678)
- PowerSeries Pro HS2TCHPRO Installation Manual; User Guide — DSC official documentation
Error Codes
Keypad and panel troubles display on this device using **[*, 2] (where supported) or dedicated trouble LEDs. Use the host panel install manual** for full trouble lists — below covers common keypad-specific symptoms.
Common keypad / operator faults
| Display / symptom | Meaning | First checks |
|---|---|---|
| Blank / dead display | No power or bus communication | AC, battery, bus wiring, keypad address, fuse |
| Keypad Tamper | Enclosure opened or tamper switch | Mounting plate, tamper jumper, cover fit |
| Cannot Arm / Not Ready | Open zones or active troubles | [*, 2] trouble scroll; close zones; clear troubles |
| Invalid Code / Access Denied | Wrong user code or authority level | User [5] programming; verify partition assignment |
| Corbus Keypad Missing | Neo/Pro lost keypad on bus | Corbus homerun, [902] enrollment, address duplicate |
| Pro Partition Mismatch | Keypad on wrong partition scope | Pro global vs partition keypad assignment in DLS |
| Cannot Enter Programming | Keypad lacks installer authority | Installer code [*, 8]; partition/global assignment |
| Touchscreen Freeze / Cal | UI not responding | Power cycle, firmware, bus current, factory reset per manual |
HS2TCHPRO
- HS2TCHPRO prox reader faults do not appear on Neo HS2TCHP programming — Pro-only options.
HS2TCHPRO touchscreen
Prox faults on HS2TCHPRO use Pro programming options — not Neo HS2TCHP menus. Black screen usually Corbus power, not touchscreen hardware.
Panel trouble reference
Keypads display panel-level troubles (AC loss, FTC, zone faults) — fix the underlying circuit or device, not the keypad, when [*, 2] points to panel/comms/zone issues.
Source: PowerSeries Pro HS2TCHPRO Installation Manual; User Guide; host panel user/install manual trouble sections.
| Code | Meaning | Suggested Fix |
|---|---|---|
| Blank / dead display | No power or bus communication | AC, battery, bus wiring, keypad address, fuse |
| Keypad Tamper | Enclosure opened or tamper switch | Mounting plate, tamper jumper, cover fit |
| Cannot Arm / Not Ready | Open zones or active troubles | `[*, 2]` trouble scroll; close zones; clear troubles |
| Invalid Code / Access Denied | Wrong user code or authority level | User `[5]` programming; verify partition assignment |
| Corbus Keypad Missing | Neo/Pro lost keypad on bus | Corbus homerun, `[902]` enrollment, address duplicate |
| Pro Partition Mismatch | Keypad on wrong partition scope | Pro global vs partition keypad assignment in DLS |
| Cannot Enter Programming | Keypad lacks installer authority | Installer code `[*, 8]`; partition/global assignment |
| Touchscreen Freeze / Cal | UI not responding | Power cycle, firmware, bus current, factory reset per manual |