Overview
TL300 universal IP communicators add Ethernet alarm reporting via dialer capture or compatible interface for panels without built-in IP modules.
Reporting path
Universal IP (T-Link)
At a Glance
| Detail | Value |
|---|
| Product type | Alarm communicator / reporting module |
|---|
| Model family (TL300, TL300CF) | See label and install manual |
|---|
| Reporting path | Universal IP (T-Link) |
|---|
| Primary manual | TL300 Installation Manual; TL300CF Installation Instructions Kit Addendum |
|---|
| Region / listing notes | TL300CF = commercial fire IP variant |
|---|
Before You Install or Replace One
- Confirm exact model number on the communicator label matches the install manual.
- Verify host panel family — Keybus PowerSeries, Neo Corbus, MAXSYS Combus, IMPASSA integrated, or universal dialer-capture are not interchangeable.
- Confirm monitoring receiver and account accept this communicator format (Contact ID, SIA, IP, cellular).
- Check carrier/network generation (3G sunset, LTE band, Ethernet path) for your region.
- Add communicator current draw to panel battery standby calculation where the module loads from panel bus power.
Official Sources
- Product page: DSC Universal Internet Alarm Communicator (ID 143)
- TL300 Installation Manual; TL300CF Installation Instructions Kit Addendum — DSC official documentation
Error Codes
Communicator faults appear on the host panel trouble display ([*, 2] on keypads where supported) and in DLS/dealer tools — the communicator itself may show LED status per its install manual.
Common communicator troubles
| Panel / display | Meaning | First checks |
|---|---|---|
| FTC / Failure to Communicate | Report did not reach central station | Account, path, format, receiver online |
| Alt. Comms AC / Battery | Communicator power fault | Module power wiring, panel AUX budget, battery size |
| Alt. Comms FTC | Alternate path failed | Test primary and backup paths separately |
| TLM / Line fault | Dialer line or seizure issue | Tip/Ring wiring, ~50 VDC idle line, panel dialer programming |
| T-Link Network Fault | IP path cannot reach network | LAN cable, router, firewall, receiver IP |
| T-Link Receiver Trouble | IP path cannot reach receiver | Receiver address, DNS, DSC/T-Link service status |
Universal TL300 IP dialer capture
- Requires Ethernet at communicator — unlike 3G4010, no cellular fallback on base TL300 universal SKU.
- T-Link Receiver Trouble with good link light often means wrong receiver IP programmed in module.
Universal TL300 IP dialer capture
| LED / panel | Meaning |
|---|---|
| Link off | Ethernet fault at module |
| Link on, Receiver Trouble | T-Link receiver IP/account |
| TLM on panel | Dialer capture wiring before IP path matters |
Requires Ethernet at premises — no cellular fallback on base TL300 universal.
LED / module diagnostics
Refer to TL300 Installation Manual; TL300CF Installation Instructions Kit Addendum for communicator-specific LED patterns and DLS module status screens.
Source: Host panel install manual § communicator / alt-comms troubleshooting; TL300 Installation Manual; TL300CF Installation Instructions Kit Addendum.
| Code | Meaning | Suggested Fix |
|---|---|---|
| FTC / Failure to Communicate | Report did not reach central station | Account, path, format, receiver online |
| Alt. Comms AC / Battery | Communicator power fault | Module power wiring, panel AUX budget, battery size |
| Alt. Comms FTC | Alternate path failed | Test primary and backup paths separately |
| TLM / Line fault | Dialer line or seizure issue | Tip/Ring wiring, ~50 VDC idle line, panel dialer programming |
| T-Link Network Fault | IP path cannot reach network | LAN cable, router, firewall, receiver IP |
| T-Link Receiver Trouble | IP path cannot reach receiver | Receiver address, DNS, DSC/T-Link service status |
| LED / panel | Meaning | |
| Link off | Ethernet fault at module | |
| Link on, Receiver Trouble | T-Link receiver IP/account | |
| TLM on panel | Dialer capture wiring before IP path matters |