Overview
2GIG Z-Wave smart home module — thermostat, dimmer, plug, outlet, or garage door controller enrolled on the panel Z-Wave network for automation and Alarm.com scenes.
On 2GIG systems, wireless devices are supervised zones on the panel — tamper, low battery, and missing signals appear as trouble conditions that may block arming depending on panel programming.
At a Glance
| Specification | Details |
|---|---|
| Protocol | Z-Wave / Z-Wave Plus |
| Host | Panel internal Z-Wave radio |
| Examples | STZ-1 thermostat, dimmer modules, smart garage controller |
| Exclusion | Must exclude from prior hub before adding to 2GIG |
What This Device Does Well
Provides reliable supervised status at the panel and Alarm.com when installed, enrolled, and range-tested correctly.
Before You Service or Replace One
- Sensor SKU — standard 345 MHz vs eSeries encrypted vs ePlus 900 MHz.
- Panel online — resolve panel AC/cell trouble before blaming sensor.
- Range — repeaters (RPTR1) or transceivers (XCVR2) for distant zones.
- Battery type — use listed cell; replace all batteries in multi-cell devices.
- Tamper — cover fully closed before declaring hardware fault.
Official Sources
- 2GIG product page
- 2GIG Full Catalog English
- 10023748a x3 installandprogrammingguide
- SSA1 SSA2 Instruction Manual
- 2GIG Edge Smart Home Manual 1
- 2GIG Edge User Guide 1
- 2GIG GC2 User Guide
- 2GIG GC2 User Guide FR
- 2GIG GC2 User Guide PO
- 2GIG GC2 User Guide SP
Use official 2GIG PDFs and install guides for exact wiring, enrollment, and firmware — specifications vary by SKU and region.
FAQs
Why does my zone show trouble?
Most common: low battery, tamper open, out of range, or wrong sensor type for the panel receiver (345 MHz vs ePlus 900 MHz).
How do I replace a sensor?
Delete old zone in installer programming, enroll replacement using Learn mode, and test walk test at final location.
Will Alarm.com show this device?
When the panel has active interactive service, enrolled zones appear in the Alarm.com app with status matching the panel.
Where is official documentation?
- 2GIG product page
- 2GIG Full Catalog English
- 10023748a x3 installandprogrammingguide
- SSA1 SSA2 Instruction Manual
- 2GIG Edge Smart Home Manual 1
- 2GIG Edge User Guide 1
- 2GIG GC2 User Guide
- 2GIG GC2 User Guide FR
- 2GIG GC2 User Guide PO
- 2GIG GC2 User Guide SP
Primary reference: 2GIG Z-Wave device enrollment guide
How do I test after installation?
Use panel walk test, zone status, and (if monitored) central station test per dealer procedure.
Can I mix 345 MHz and ePlus sensors?
ePlus 900 MHz sensors require XCVR2 transceiver hardware — they do not enroll on the standard 345 MHz receiver alone.
Why does my zone show trouble?
Most common: low battery, tamper open, out of range, or wrong sensor type for the panel receiver (345 MHz vs ePlus 900 MHz).
How do I replace a sensor?
Delete old zone in installer programming, enroll replacement using Learn mode, and test walk test at final location.
Will Alarm.com show this device?
When the panel has active interactive service, enrolled zones appear in the Alarm.com app with status matching the panel.
Where is official documentation?
- 2GIG product page
- 2GIG Full Catalog English
- 10023748a x3 installandprogrammingguide
- SSA1 SSA2 Instruction Manual
- 2GIG Edge Smart Home Manual 1
- 2GIG Edge User Guide 1
- 2GIG GC2 User Guide
- 2GIG GC2 User Guide FR
- 2GIG GC2 User Guide PO
- 2GIG GC2 User Guide SP
Primary reference: 2GIG Z-Wave device enrollment guide
How do I test after installation?
Use panel walk test, zone status, and (if monitored) central station test per dealer procedure.
Can I mix 345 MHz and ePlus sensors?
ePlus 900 MHz sensors require XCVR2 transceiver hardware — they do not enroll on the standard 345 MHz receiver alone.